×

FDF100VNAVD2

10.0 ( 4.0 ~ 11.2 ) Floor Standing Single Split PAC

FDF100VNAVD2

Floor Standing : 10.0 ( 4.0 ~ 11.2 )

Indoor Unit - FDF100VD2 / Outdoor Unit - FDC100VNA
Nominal cooling capacity of 10.0kW

R410A
  • FDF100VD2
  • FDF100VD2

    Indoor Unit : FDF100VD2

    FDC100VNA

    Outdoor Unit : FDC100VNA

  • FDC100VNA
Indoor unitFDF100VD2
Outdoor unitFDC100VNA
Power source1 Phase 220-240V, 50Hz / 220V, 60Hz
Nominal cooling capacity (Min~Max)kW10.0 ( 4.0 ~ 11.2 )
Nominal heating capacity (Min~Max)kW11.2 ( 4.0 ~ 12.5 )
Power consumptionCooling/HeatingkW3.12 / 2.94
EER/COPCooling/Heating3.21 / 3.81
Inrush currentA5
Max. running currentA24
Sound power
level*1
IndoorCooling/HeatingdB(A)65 / 65
OutdoorCooling/Heating70 / 70
Sound pressure
level*1
IndoorCooling (Hi/Me/Lo/Ulo)54 / 50 / 48 / 44
Heating (Hi/Me/Lo/Ulo)54 / 50 / 48 / 44
OutdoorCooling/Heating54 / 56
Air flowIndoorCooling (Hi/Me/Lo/Ulo)m3/min29 / 26 / 23 / 19
Heating (Hi/Me/Lo/Ulo)29 / 26 / 23 / 19
OutdoorCooling/Heating75 / 73
Exterior DimensionsIndoorHeight x Width x Depthmm1,850 x 600 x 320
Outdoor845 x 970 x 370
Net weightIndoor / Outdoorkg52 / 80
RefrigerantType/GWPR410A/2088
RefrigerantChargekg/TCO2Eq3.8/7.934
Refrigerant piping sizeLiquid/Gasø mm9.52(3/8") / 15.88(5/8")
Refrigerant line (one way) lengthmMax.50
Vertical height differencesOutdoor is higher/lowermMax.50 / Max.15
Outdoor operating
temperature range
Cooling*2°C-15~50
Heating-20~20
Air filter quantityPlastic net x 1(Washable)
Remote control (option)wired:RC-E5 (installed) wireless:RCN-KIT4-E2 (option)
Energy Class (Cooling/Heating)A+/A+
SEER5.7
SCOP (Average climate)4
Pdesign (cooling/heating(@-10°C))kW10.0/8.5
Annual Electricity Consumption (cooling/heating)kWh/a614/2978
Designated Heating SeasonAverage
The data is measured under the following conditions (ISO-T1).
Cooling: Indoor temp. of 27°CDB, 19°CWB, and outdoor temp. of 35°CDB. Heating: Indoor temp. of 20°CDB, and outdoor temp. of 7°CDB, 6°CWB.
  1. : Indicates the value in an anechoic chamber. During operation these values are somewhat higher due to ambient conditions.
  2. : If a cooling operation is conducted when the outdoor air temperature is –5 ̊C or lower, the outdoor unit should be installed at a place where it is not influenced by natural wind. If wind blows, the low pressure will drop and compressor frequency will increase, this will cause the capacity to drop and may cause the unit to break down.